Wheeled Excavator Lift Charts: Capacity, Reach and Stability

Time : Oct 31, 2026

A Wheeled Excavator lift chart gives the rated load for a specific working radius, lift point height and machine configuration. The usable capacity is the value that applies throughout the intended movement, after accounting for the equipment and conditions specified by the chart. A capacity quoted at short reach cannot be assumed at a longer radius, even when the load itself has not changed.

A valid assessment starts with the chart for the exact machine and attachment configuration. Boom and arm length, counterweight, tires, blade and outriggers can all affect the published values. The chart notes are part of the rating: a table without its configuration diagram and load definitions is incomplete.

Reading Radius, Height and Rated Load

Working radius is normally the horizontal distance from the center of upperstructure rotation to the vertical line through the load or lifting point, as defined on the chart. It is not the length of the boom, the distance from a tire, or the horizontal projection of the arm alone. Lift point height is referenced to the level specified by the manufacturer, often the machine support level. Use the chart diagram to establish both reference points before selecting a value.

Find the column for the relevant radius and the row for lift point height. Some charts list capacities at maximum reach instead of a fixed radius; that value applies only to the geometry described in the chart. If the planned position falls between listed points, follow the manufacturer's interpolation instructions. Where no method is given, use a more conservative applicable value or obtain a confirmed rating; do not assume a smooth progression between cells.

The load follows an arc as the boom, arm and upperstructure move. The controlling chart position may therefore occur during travel between the pick and placement points, not at either endpoint. Plan against the most restrictive applicable rating along the entire path, including any increase in radius caused by lowering or slewing the load.

What the Capacity Includes

Charted capacity and the weight of the material being lifted are not necessarily the same. The applicable load definition determines which items must be counted or deducted. Depending on the chart, these can include the hook, lifting link, quick coupler, bucket or other attachment, slings, shackles and any load-handling device. Do not deduct an attachment twice if its weight is already included in the chart configuration.

For example, if a chart permits a gross suspended load of 2,000 kg at a planned position and the applicable rigging weighs 100 kg, the remaining allowance for the object is 1,900 kg. This is an arithmetic illustration, not a machine rating. The actual chart may define the reference differently or require additional deductions.

The load's center of gravity also matters. An offset lifting point, a long component or a shifting load can place the effective load line farther from the rotation center than expected. Measure the working radius to the actual load line under tension and account for clearance needed to keep the load from contacting the machine or nearby structures.

Hydraulic Limit Versus Stability Limit

A lift chart may distinguish values limited by hydraulic capability from those limited by stability. Hydraulic capacity reflects the force available to hold or move the boom and arm at a particular geometry. Stability capacity reflects the machine's resistance to tipping about its support boundary. Symbols, shading or notes identify the distinction on the applicable chart; their meaning should never be transferred from another model's chart without verification.

At greater radius, the load creates a larger overturning moment. A machine that lifts a load close to its chassis may reach its stability limit when that same load is extended. Conversely, a short-radius position can be limited by cylinder force or geometry rather than by tipping. Both limits must be respected, and the lower applicable rated value governs.

Direction of lift is equally important. Over-front, over-rear and over-side ratings can differ because the support footprint and counterweight orientation change relative to the load. A slew from the front to the side can pass into a lower-capacity sector even when radius and height remain nearly constant. Where a chart supplies a single all-around rating, confirm that it covers the entire intended slew.

Outriggers, Blade and Ground Support

A chart for outriggers fully deployed assumes the deployment and contact conditions stated in its notes. Partially extended outriggers, a raised blade or lifting on tires are different configurations; use their corresponding published ratings. Do not interpolate between an on-tires chart and an outrigger chart simply because the stabilizers are touching the ground.

Outrigger contact alone does not establish a stable base. Soft fill, trench edges, buried voids and uneven surfaces can allow a pad to settle or tilt as the load moves. Support materials must distribute reaction forces over ground with adequate bearing capacity, and the machine must be leveled within the manufacturer's stated limits. A small change in machine inclination alters the load radius and shifts the effective center of gravity; the chart rating for level ground does not automatically apply on a slope.

Tire configuration matters when lifting on wheels. Tire size, condition, inflation and axle-lock or oscillation-lock settings should match the chart requirements. A locked axle and an unlocked oscillating axle do not necessarily provide the same support behavior. Brakes and transmission settings must also follow the applicable lifting instructions.

Comparing Excavator and Loader Ratings

Equipment specifications can contain similar-looking figures that describe different tasks. The SDSG FC948 Wheel Loader, for example, lists a 2,500 kg rated load and a 4,500 mm unloading height. Those figures describe a loader specification; they do not establish a suspended-load capacity at an excavator's working radius or a rating for a lifting hook.

Likewise, bucket volume and digging force do not substitute for a lift chart. A suspended load can swing and impose forces in directions that differ from those created during normal digging or bucket loading. Use an approved lifting point and the rating applicable to that lifting arrangement.

Conditions That Change the Planned Lift

Chart values are based on the manufacturer's stated operating conditions. Sudden acceleration, abrupt braking or a swinging load adds dynamic forces that are not captured by a simple static weight comparison. Wind can also impose significant side force on large surface-area loads. Where conditions exceed the chart assumptions or the manufacturer's instructions, a chart value alone is insufficient to authorize the lift.

Before the load leaves its support, establish its weight and center of gravity, the lift path, the maximum radius and the lowest applicable chart value. Confirm that the lifting point, attachment and rigging are rated for their intended use and that the load is free of the ground without snagging. If a position, configuration or weight cannot be established, obtain a verified rating or revise the lift plan before proceeding.

Leave us a message

Submit